Chip Kits / Parts

HA Motorsports DIY Obd1 chip kits are a complete package for those who wish to chip their own ECU. All chip kits comprise of top quality chipping components and contain everything you will need to socket and chip your Honda ECU.

HA Motorsports DIY Obd1 chip kits are a complete package for those who wish to chip their own ECU. All chip kits comprise of top quality chipping components and contain everything you will need to socket and chip you Honda ECU.

This Hondata S300 socketing kit contains the necessary components to install a Hondata S300 into any OBD1 USDM civic/ integra ECU.

Moates Demon USDM ECU socketing kit. Contains everything necessary to install the Moates Demon into an OBD1 civic/ integra USDM ECU. This kit is included with the Demon, but if you need it separately, here it is.

This USDM '1720' board type Non-VTEC to VTEC ECU Conversion kit contains the necessary components to properly convert your Non-VTEC ECU to VTEC. After the conversion, your ECU will be electronically equivalent to a factory P28 ECU.

This USDM '11F0' board type Non-VTEC to VTEC ECU Conversion kit contains the necessary components to properly convert your Non-VTEC ECU to VTEC. After the conversion, your ECU will be electronically equivalent to a factory P28 ECU.

This USDM '1980' board type Non-VTEC to VTEC ECU Conversion kit contains the necessary components to properly convert your Non-VTEC ECU to VTEC. After the conversion, your ECU will be electronically equivalent to a factory P28 ECU.

The 27SF512 is the perfect Eprom chip for Honda ECU boards. These blank chips will allow you to program your exact tune over and over to the same chip. This chip is large enough to load two 256k rom programs onto each chip. Requires a chip programmer capable of programming 28 pin EEprom chips like the Moates BURN2.

This is the perfect 28 pin ZIF Socket (Zero Insertion Force) for OBD1 Ecu boards. The ultra low profile ZIF allows extra clearance for an ECU with a knock board and your 27SF512 Chip, or even stacking the Moates 2-Timer and Chip on top.

We are proud to offer our OBD1 ECU PWM Boost Control Kit. This kit contains the necessary components to operate the PWM Boost control features when using ECtune or Hondata S300.

The HA Motorsports custom basemap program is designed to start your custom engine setup to run diagnostics, test drive, etc. prior to dyno tuning. This basemap may also be used as a starting point for street or dyno tuning. Our custom basemap will be programmed to one of our 27SF512 chips and shipped with your exact specs.

This is our custom basemap calibration file for those who need a basemap for use with Hondata S300 / Smanager. Fully configurable to your specifications based on our tuning experience with setups similar to yours that you specify.

Our stock engine basemap chips are the solution to running your swapped engine in your chassis properly.

28 pin dip socket for USDM and JDM ECU's. Allows installation and removal of your EPROM chip.

4 pin latching header used at CN2 location on USDM ECU's. This latching header allows a secure connection of the Moates hondalog or hulog to your ECU.

Pair of .1uf ceramic capacitors for locations C51 and C52 on USDM ECU boards.

74HC373 chip. Used when socketing USDM Honda OBD1 ECU's.

Replacement 6 ft. length USB 2.0 cable. Standard A-B cable for use with Moates Ostrich, Burn1, Hulog, Hondata S300, Kpro, and other common USB 2.0 fitments.

10 foot length USB 2.0 cable. Used for connectivity with Hondata S300, Moates Ostrich/ Ostrich 2.0, Hulog, K-Pro, and Demon. This extra long USB cable will allow more room to reach your laptop and tuning devices when needed.

PNP transistor used in location Q101 on 11F0 boards when converting from non-vtec to VTEC. This PNP transistor is labeled B1030.

NPN Transistor used when converting 1720 and 1980 boards to VTEC. Used at position Q26. This transistor is labeled D1423.

Replacement 4 pin interconnect cable for use with the Moates Demon. This cable connects the Demon unit with the 4 pin datalog port at CN2. This cable is included with the Moates Demon kit, however if yours gets lost or damage, this is a replacement.